Multi-line 2 AGC-4 Mk II Application Software
您即将下载 Multi-line 2 AGC-4 Mk II Application Software
您已选择下载我们的软件。
几秒钟内,您将收到一封包含下载链接的电子邮件。
如果使用软件有问题,请联系support@deif.cn.
诚挚的祝福,
DEIF A/S
本软件受DEIF A/S版权保护。请点击上述链接可查阅DEIF A/S版权和许可协议(EULA)。
本软件适用于以下DEIF产品
您即将下载 6.14.0
与上一版本相比,主要更新如下:
IMPORTANT: This software requires USW-3 version 3.60.2 with PDB revision 10901 or higher.
PM compatibility: 1.35.1
New features:
- Added new parameter 8154 "Gnd priority". This parameter controls whether gensets or batteries should have ground relay active when their nominal sizes are equal. This parameter only has an effect if there are ASC150 Storage controllers with ground relay functionality enabled.
- EIC: Added buzzer output for Baudouin CPCB IV.
- BTB controllers can now be statically synchronized.
Changes:
- Text handling updated (this requires new USW3 for connection).
- EIC: Added M-Logic command flag to give control if preheat to Volvo EMS.
- EIC: Kohler KDI3404 - Added support of second ECU.
- EIC: Implemented Yuchai fault codes.
- GENSET: Nominal set 5 and 6 added in menu 6800 and 6810.
- GENSET: Averaged P and Q, which were introduced in version 6.08.0, can now be used for load-sharing. Use jump menu 9281.
- GENSET-MAINS: Averaged P and Q, which were introduced in version 6.08.0, can now be used for regulation and ramping. Use jump menu 9282.
- GENSET-MAINS-BTB: Averaged P, Q and S, which were introduced in version 6.08.0, can now be used for power management. Use jump menu 9283.
Corrections:
- Fixed issue of not starting unit when installing Profibus.
- Fix emulated load from ASC variants not being added correctly.
- PMS redundant with local mode update (8022) corrected. The redundant unit follows the preferred unit.
- Fixed an issue where language write failed.
- Service timers 3 and 4 now persist between power cycles of the controller.
版本号 | 发布日期 | 描述 |
---|---|---|
6.14.0 |
27/09/2024 |
IMPORTANT: This software requires USW-3 version 3.60.2 with PDB revision 10901 or higher. PM compatibility: 1.35.1 New features:
Changes:
Corrections:
|
6.13.1 |
15/07/2024 |
PM compatibility: 1.34.0 Corrections1- Corrected unit restarting if Profibus option is selected. |
6.13.0 |
18/06/2024 |
PM compatibility: 1.34.0 New features 1- Fuel optimisation further optimised in more applications, including PV and battery. Changes 1- Spinning reserve stop hysteresis calculation is now based on the nominal power on busbar after next DG to stop.
Corrections 1- Auto calculation multistarts with fuel optimisation, now works before the TB is closed. |
6.12.1 |
26/02/2024 |
PM compatibility: 1.34.0 Corrections
|
6.12.0 |
30/10/2023 |
PM compatibility: 1.32.0 New features• EIC: Added support of Weichai E6. Changes• EIC: Added GTACP (0xFE05, SPN2452/2460) to Caterpillar generic and Perkins generic. Corrections• PMS priority update in 32DG application now working correctly. |
6.11.3 |
21/09/2023 |
PM compatibility: 1.30.1 Corrections
|
6.11.2 |
14/09/2023 |
PM compatibility: 1.30.1 Corrections
|
6.11.1 |
21/07/2023 |
PM compatibility: 1.30.0 Corrections
|
6.11.0 |
11/07/2023 |
PM compatibility: 1.30.0 New features
Changes
Corrections
|
6.10.2 |
25/05/2023 |
PM compatibility: 1.29.0 Corrections
|
6.10.1 |
23/03/2023 |
PM compatibility: 1.29.0 Corrections
|
6.10.0 |
06/03/2023 |
PM compatibility: 1.29.0 New features
Changes
Corrections
|
6.09.1 |
20/01/2023 |
PM compatibility: 1.29.0 Corrections
|
6.09.0 |
23/12/2022 |
PM compatibility: 1.28.0 New features:
Changes:
Corrections:
|
6.08.1 |
13/12/2022 |
PM compatibility: 1.28.0 Corrections:
|
6.08.0 |
17/11/2022 |
PM compatibility: 1.28.0 New features:
Changes:
Corrections:
|
6.07.0 |
11/07/2022 |
PM compatibility: 1.25.0 New features:
Corrections:
|
6.06.0 |
18/02/2022 |
PMS compatibility: 1.25.0 New features: Finetuning: |
6.05.0 |
01/02/2022 |
PM compatibility: 1.24.2 New features:
Changes:
Corrections:
|
6.04.3 |
16/11/2021 |
PM compatibility: 1.24.1 Corrections:
|
6.04.2 |
10/11/2021 |
PM compatibility: 1.24.1 Corrections:
|
6.04.1 |
22/10/2021 |
Not UL approved version PM compatibility: 1.24.1 Corrections:
|
6.04.0 |
07/10/2021 |
Not UL approved version PM compatibility: 1.24.1 New features:
Changes:
Corrections:
|
6.03.1 |
13/09/2021 |
Not UL approved version PM compatibility: 1.24.1
|
6.03.0 |
15/07/2021 |
Not UL approved version PM compatibility: 1.24.1 New features:
Changes:
Corrections:
|
6.02.1 |
06/05/2021 |
UL approved version PM compatibility: 1.23.0 Corrections:
|
6.02.0 |
06/04/2021 |
Not UL approved version PM compatibility: 1.23.0 New features:
Changes:
Corrections:
|
6.01.2 |
15/03/2021 |
Not UL approved version PM compatibility: 1.22.0 Corrections:
|
6.01.1 |
12/02/2021 |
Not UL approved version PM compatibility: 1.22.0 Corrections:
|
6.01.0 |
11/01/2021 |
UL approved version PM compatibility: 1.22.0 New features:
|
6-00-0 |
07/01/2021 |
Not UL approved version PM compatibility: 1.22.0 |
在此页面,您可以下载产品的更新软件,并使用各种实用工具和附加组件设置、检测故障和配置产品。
请注意,用户无法更新我们的所有产品。同时也不是所有产品都配有实用工具。因此,本页的软件列表不能视为DEIF产品的概述。
DEIF将登记您注册的下载邮箱地址,以便在未来需要时发送有关的更新信息。
DEIF不对产品更新失败或使用实用工具造成的任何后果负责。DEIF A/S也不对软件升级导致的产品行为变化的后果负责。用户始终有责任在调试前确保正确的设置和配置。请在更新产品之前查阅软件的更新日志。
www.deif.cn软件下载许可协议
下载的软件仍是DEIF的财产。本软件不得用于商业目的分发, 不得全部或部分更改或重复使用,也不得出售给任何第三方。
最新版本,功能齐全
我们始终建议您安装最新版本的软件,以充分利用您的DEIF产品。
所有更新的软件都可以从www.deif.cn->支持->下载->软件栏目下下载。
如果您在查找产品的相关软件时有任何疑问或问题,请随时致电丹控电气(上海)有限公司,电话: +86 21 68796200,或者发送电子邮件至support@deif.cn, 我们随时为您服务。