Multi-line 2 EC-1/GC-1 Application Software Std. Lang. Package series 1.x.

您即将下载 Multi-line 2 EC-1/GC-1 Application Software Std. Lang. Package series 1.x.

您已选择下载我们的软件。

几秒钟内，您将收到一封包含下载链接的电子邮件。

如果使用软件有问题，请联系support@deif.cn.

诚挚的祝福，

DEIF A/S

本软件受DEIF A/S版权保护。请点击上述链接可查阅DEIF A/S版权和许可协议(EULA)。

本软件适用于以下DEIF产品

您即将下载 1.43.4

与上一版本相比，主要更新如下：

This software applies to the following DEIF products:

  • Multi-line 2 - EC-1/GC-1

Changes:

  • Status of cable supervision in USW optimised
版本号 发布日期 描述

1.43.4

08/10/2010

This software applies to the following DEIF products:

  • Multi-line 2 - EC-1/GC-1

Changes:

  • Status of cable supervision in USW optimised

1.43.3

18/08/2009
  • Wire break symbol in Chinese added.

1.43.2

18/06/2008
  • Binary inputs with cable supervision updated.

1.43.1

04/02/2008
  • Energy counter updated.

1.43.0

15/01/2008
  • Multi input wirebreak failclass changed to warning

1.42.3

02/11/2007
  • Multiinput wirebreak alarm updated.

1.42.2

22/06/2007
  • SW version number corrected.

1.42.1

19/06/2007
  • Extended stop updated when using frequency as running feedback.
  • Remote puls start updated during cooldown

1.42.0

14/05/2007

New features:

  • New digital input function, remote puls start
  • New digital input function, remote puls stop
  • New relay output function, auto mode indication

Changes:

  • Mode (Auto/Local) is not stored, if power is removed from the controller.

1.41.2

28/02/2007
  • Busbar transformer setting updated.

1.41.1

19/02/2007

Changes:

  • Engine running relay now reacts to running feedback.
  • Ext stop is now performed when running feedback is lost.
  • Failclass error corrected in Hz / V failure alarm

1.41.0

03/01/2007

Changes:

  • Shutdown possibility during start sequence added
  • 4-20 mA input range improved.

1.40.4

01/10/2006

Changes:

  • MB open / close feedback updated

1.40.3

22/08/2006

Changes:

  • Chinese texts updated.
  • Icons updated.
  • CanOpen remote start/stop updated.
  • Firepump updated with CAN alarm.
  • Alarm relay B updated.
  • Low power readout for USW scaled.
  • Oilpressure readout for USW scaled.
  • PF calculation updated.

1.40.2

21/03/2006

Changes:

  • L1-0 error message updated

1.40.1

08/03/2006

Changes:

  • Running hour counter updated.
  • MB handling upon power up changed

1.40.0

08/02/2006

New features:

  • VDO 3 range increased to 2400 ohm.
  • External heater function added.
  • New stop coil function added - stop coil no start
  • L1-N value error alarm added.
  • Mains failure frequency detection ON/OFF function added.
  • Additional view added.
  • Parameter groups added.
  • GC-1 frequency readings shown with 1 decimal.
  • Power readings shown with 1 decimal if Pnom < 49kW.
  • Diode compensation function added.
  • Test input added for AMF.
  • New digital input texts added.
  • New text "Coolant pressure" added to analog input (4-20mA).
  • External trip of MB added to AMF sequences.
  • Extra password level added.
  • GB breaker delay function added.
  • Oilpressure feedback added.

Changes:

  • Some parameter settings updated.

1.30.5

29/11/2005

New features:

  • New AMF situations added.
  • Run status alarm added.

Changes:

  • Fuel pump function updated.
  • Stop coil funciton updated.
  • Input functions updated (Idle run, firepump).
  • Alarm / limit relay functions updated.
  • Default settings updated (Charger gen).
  • Breaker interlock updated.
  • Start enable updated.
  • Parameter menu updated.
  • Setting of voltage transformers updated.
  • Language handling updated.
  • AMF functions updated.
  • VDO user definable inputs updated.
  • Run enable updated.
  • Block (shutdown) updated.
  • HW change to VDO inputs supported.
  • Device number for options in USW updated.

1.30.2

21/10/2005

Changes:

  • Tacho feedback updated
  • E counter updated

1.30.1

05/10/2005

Changes:

  • Test function updated.

1.30.0

05/10/2005

New features:

  • Italian and Chinese language supported.
  • Option H1 (CANopen) added.
  • 1 second delay added to starter and tacho feedback

Changes:

  • Writing of outputs from USW corrected.
  • Cool down timer updated remote mode.

1.20.1

12/09/2005

Changes:

  • Test function updated

1.21.0

12/09/2005

New features:

  • German, Spanish and French language supported.

Changes:

  • Nominal voltage is phase-phase
  • D+ timer updated
  • Firepump updated
  • "f/U..." texts changed

1.20.0

03/08/2005

New features:

  • Support for 3-phase measurementboard (GC-1)
  • Support for option B3 (GC-1 AMF)

1.10.2

04/07/2005

Changes:

  • Configurable outputs updated

在此页面，您可以下载产品的更新软件，并使用各种实用工具和附加组件设置、检测故障和配置产品。

请注意，用户无法更新我们的所有产品。同时也不是所有产品都配有实用工具。因此，本页的软件列表不能视为DEIF产品的概述。

DEIF将登记您注册的下载邮箱地址，以便在未来需要时发送有关的更新信息。

DEIF不对产品更新失败或使用实用工具造成的任何后果负责。DEIF A/S也不对软件升级导致的产品行为变化的后果负责。用户始终有责任在调试前确保正确的设置和配置。请在更新产品之前查阅软件的更新日志。

www.deif.cn软件下载许可协议

下载的软件仍是DEIF的财产。本软件不得用于商业目的分发, 不得全部或部分更改或重复使用，也不得出售给任何第三方。

最新版本，功能齐全

我们始终建议您安装最新版本的软件，以充分利用您的DEIF产品。

所有更新的软件都可以从www.deif.cn->支持->下载->软件栏目下下载。

如果您在查找产品的相关软件时有任何疑问或问题，请随时致电丹控电气(上海)有限公司，电话: +86 21 68796200，或者发送电子邮件至support@deif.cn, 我们随时为您服务。

更多信息